#FAKE SEPTUM PIERCING MANUAL#
#FAKE SEPTUM PIERCING ISO#

This formula expresses the relationship between the load in a bolt and applied torque. To determine an estimated torque value, use the standard torque formula: T = DFK. Tightening torque for SAE bolts: UNC and UNF 1/4 1-1/2 Not Lubricated and Lubricated Grade 1, Grade 2, Grade 5/5.2, Grade 8 Tightening torque for METRIC bolts: Standard and Fine Pitch M6 M36 Not Lubricated and Lubricated Class 4.6, Class 8.8, Class 10.9, Class 12.9 Wrench / Spanner Interchange Chart SAE METRIC, 10 most common sizes An under-torqued bolt will deform and won’t be able to provide as much clamping force as needed, while an over-torqued bolt will break. PASS 3 Torque Sequence: Torque to the final torque value (100%). PASS 2 Torque Sequence: Torque to a maximum of 60% of the final torque value. Check that gasket is getting compressed uniformly. PASS 1 Torque Sequence: Torque to a maximum of 30% of the final torque value in accordance with the torque sequence. Torque bolts and nuts in a “CRISS-CROSS” sequence using a minimum of three torquing passes and the maximum bolt stress as defined. Here’s an example metric bolt specification: M8-1.0 x 20. For nuts the size dimensions used are simply diameter and pitch. But the size of a metric fastener is more accurately specified using diameter, pitch and length dimensions, in millimeters. Metric nuts and bolts are commonly referenced using ‘M’ sizes, for example: M3, M8, M12. Once the clamp load is determined, finding the correct torque value for a bolt is one simple calculation away. Bolt Dimensions Metric Grade Markings Torque Values Applications ENGINE 163-224 cc 270-459 cc Name Size Torque Value Size Torque Value Nm ft-lb Nm ft-lb Connecting Rod Bolt M7 12 9 M8 18 13 Cylinder Head Bolt M8 24 18 M10 39 29 Flywheel Nut M14 75 55 M16 115 85 Crankcase Cover Bolt M8 24 18 M8 25 18The proof load itself is usually 85% to 95% of a bolt’s yield strength, but the clamp load is significant because it is what ultimately provides the clamping pressure. Below is a list of the recommended tightening torques for 12.9 / 10.9 / 8.8 zinc plated finish bolts. Torque Tightening Values for Structural Steel Bolts.

#FAKE SEPTUM PIERCING MANUAL#

While it's best to go by the shop manual this chart will give you a quick reference when the shop manual is not handy. Often times I'm asked what the torque specs are on some of the bolts on a Spyder. Torque Specs for Metric Bolts Torque Specs for Metric Bolts. Values though 7/16-inch diameter are stated in inch-pounds: ½-inch and over are stated in foot-pounds.

For other friction conditions, significant modifications may be required.

#FAKE SEPTUM PIERCING ISO#

Need the EZ to read torque chart but the Inch (imperial) version?Class 4.6 ISO Metric Coarse Pitch Bolts and Screws Diameter Pitch (mm) Bolt Tension Corresponding to 65% of Proof Load kN Recommended Assembly Torque Nm M1.6 0.35 0.19 0.06 M2 0.40 0.31 0.12 M2.5 0.45 0.50 0.25 M3 0.50 0.73 0.44 M4 0.70 1.29 1.0 M5 0.80 2.08 2.1 M6 1.00 2.94 3.5 M8 1.25 5.34 8.5 M10 1.50 8.45 17 The following torque values are suggested maximums based upon actual lab testing on clean and dry or near dry fasteners. If you need to go from In/lbs to Ft/lbs multiply that by 12, but I really shouldn't have to tell you that.

IF YOU WANT THEM IN Newton Meters then multiply the Ft/LBS value by 1.3558179 to get Nm. Metric Dimensions: M10-1.50 x 15mm, Grade: 9.8 (Heavy Duty) Made in the USA from, Heat-Treated, hardened alloy steel.NOTE : ALL TORQUE VALUES IN IN IMPERAL (INCH) MEASURES. These bolt kits are the strongest bolts you can get to attach your torque converter and are used in competitions.

Fake septum piercing